The OBDII trouble password of P0335 is well-known as a “hard” code, meaning severely detrimental come the operation of her Accord engine. An ext specifically the DTC P0335 to represent a lack of signal native the crankshaft place sensor. The crankshaft position sensor in her Honda Accord notifies your ECU of the crankshaft speed and current location.

You are watching: 2005 honda accord camshaft position sensor location

Without this data, the engine will either no run or run very poorly. Typical symptoms are difficulty starting or the engine may shut turn off randomly, creating a really dangerous case for not only the driver but the passengers together well.

Possible reasons of OBDII examine engine light P0335Bad or weak batteryBad StarterBad crankshaft position sensorDamaged sensor harness

Today I’ll be reflecting you just how to service and also replace your crankshaft position sensor in a 2000 Honda Accord with a F23A1 VTEC SOHC engine.

The part number for this component is 37840-P0A-A01 for the crankshaft position sensor in your Honda Accord. The can additionally be discovered under the component number of 37840-PAA-A01.


*

This How To change a Honda Accord Crankshaft place Sensor DIY guide assumes you have already removed her driver side engine mount and supported her engine v a jack. Please inspect our just how To adjust a Honda Accord time Belt overview for an ext details.

Before you start our DIY overview on how To readjust a Honda Accord Crankshaft position Sensor, you must disconnect the an unfavorable terminal on her battery. As stated previously, this overview assumes you deserve to raise and also lower her F23 already, which is obligated when an altering your time belt.

*

Unplug your four pin connector that runs to her crankshaft position sensor in her Honda Accord. Here’s what your pigtail looks like mounted to her F23A1. It’s secured by a 10mm bolt that runs through the ago of her VTEC SOHC engine.

*

This exploit to your crankshaft position sensor runs with your lower timing plate, which need to be eliminated to change a Honda Accord Crankshaft position Sensor. In bespeak to perform this, you must lower your engine if still associated to her chassis, and remove the crankshaft sheave or harmonic balancer.

This might be difficult if you room working ~ above the ground with hand tools and don’t have a air compressor through the ideal air tools. Usage a Honda crankshaft wrench, Moroso part number 61805 to effectively loosen your crankshaft bolt without air tools.

*

With the bolt removed, girlfriend should be able to wiggle off your crankshaft wheel and collection it safely come the side. Do sure remove your woodruff key and store that as safe as your pulley.

*

Now you have the right to remove every the 10mm bolts that host your lower timing sheathe in place. Eliminate these distinct bolts and also then do your method to the valve cover, friend will need to back off the valve sheathe bolts the run v to the cylinder head.

Loosen every the valve covering bolts, however do no remove and also gently loosen your valve cover. Background the valve sheathe to enable enough an are for your top SOHC VTEC time cover come come off her engine. There space 2 10mm bolts that run through the upper cover come the cylinder head, eliminate these to loosen your top timing cover.

*

Now slide off your lower timing cover and also pull down to release from her side motor mount. You need to now watch your timing belt assembly and also your F23A1 balance shafts and also belts. The crankshaft place sensor in your Honda Accord is situated behind the crank cause plate.

*

You have the right to take one of two routes to removing your crankshaft position sensor and replacing it. You have the right to loosen her timing belt tensioner bolt, the longated bolt situated in the middle of her tensioner arm. This should enable enough slack regarding gently back off your reduced crank sheave plate and undo the 10mm bolt the holds the crankshaft position sensor in place.

*

If this is not an choice for you, examine out our how To adjust a Honda Accord timing Belt guide on just how to properly time and also remove your F23A1 belts to organization your crankshaft position sensor.

There are numerous timing marks for your balance obelisk that we recommend you line as much as TDC before removing your balance pillar belts.

See more: Do You Know How To Say Dragon In French, How To Say Dragon In French

*

Before removing your balance pillar belts come reach your crankshaft position sensor, friend will require to twin check time marks to ensure her F23a1 is at TDC. Again for an ext details check our just how To DIY guide on changing the Honda Accord time belt.

*

Once you have actually replaced her Honda Accord crankshaft position sensor, you can use a scan device to properly clear your OBDII check engine password of P0335. Hope we’ve assisted you learn how To adjust a Honda Accord Crankshaft place Sensor, if girlfriend have any questions you re welcome leave us a comment below!