JavaScript is disabled. Because that a better experience, please allow JavaScript in her browser prior to proceeding.

You are watching: 2002 vw passat oil pressure sensor location


2002 jetta GLS 2.0i am looking to adjust my oil pressure sender/switch yet i cannot locate it, mine oil irradiate blinks every now and then, i was said the senders go bad often and also to shot replacing it, i have actually no oil leaks, just changed the oil and brand-new filteri likewise have noticed that when i revolve on the automobile in the morning, if idle is fine, as quickly as ns pull turn off there is part blue exhilaration trail, only in the morning as soon as i traction off, go not occur again, anyone recognize why that can be?
Hi there. In mine 1.8t the oil press sensor is at the bottom that the engine, close to the screw to empty the oil, in the direction of the ideal hand side. About the blue smoke... I honestly dont know :s can it it is in a leak indigenous somewhere, or a poor mix with the fuel? Im simply guessing... Hope u sort it out!Sent from mine A0001 utilizing Tapatalk
This is indigenous the Bently...."This switch is located on the oil filterflange for both gas and diesel engines, watch Oil filterflange assembly, offered later.""Oil push switch (F1)• Tighten come 25 Nm (18 ft-Ib)• black plastic housing• closes at 1.4 bar (20 psi)"right over the oil cooler/oil filter. Think it"s the exact same for the 2.0 together well...
Hi there. In my 1.8t the oil pressure sensor is at the bottom that the engine, close to the screw to north the oil, in the direction of the ideal hand side. Around the blue smoke... I honestly dont know :s might it be a leak indigenous somewhere, or a negative mix v the fuel? Im just guessing... Hope u kind it out!Sent from mine A0001 using Tapatalk
Should it is in this male right here. The picture is rotated, the threaded section actually points down when mounted on the engine.

See more: What Does Bene Mean In Italian + Meaning!, Italian Expression Of The Day: 'Va Bene'



Should be this man right here. The photo is rotated, the threaded ar actually points under when installed on the engine.

What about the ar of said component on a 12v VR6 AFP? My first VR and I"m considering including an oil pressure gauge for sh*ts and also giggles. Göösemister
~ Matt
2004 GTI GLS 1.8T #SophiaTheGTI - Current:laugh:2002 Jetta Wagon GLS VR6 RIP #OliveTheWagon - unable to do :banghead:2000 Golf GLS RIP "Indy" - unable to do
*
facebook | instagram
Oil press switch ar on 2000 Golf Mk4 VR6 Gti?
Ive been trying to find where the oil push switch is located, iver searched nice much all over online to shot and uncover where it can be on my golf, ive searched close to the ideal side near the aux pump and the distributor and also down close to the oil pan and I cant find it anywhere! Id greatly appreciate the anyone might show/tell me where it might be? give thanks to you!!
Ive been searching for where the oil press switch is located, iver searched nice much almost everywhere online to shot and discover where it could be on my golf, ive searched close to the best side near the aux pump and the distributor and also down near the oil pan and also I cant discover it anywhere! Id substantially appreciate that anyone could show/tell me wherein it could be? thank you!!
By now you"ve found it (or tossed the car). It"s darn-near impossible to check out the location!You can find it by feeling though: It"s situated ON height OF the oil filter housing.It"s most basic to purchase a brand-new figure-8 o-ring and replace that at the very same time:- Jack increase car- relocate plastic shield under engine (if still there)- remove filter- eliminate 3 bolts (12 or 13mm) holding housing in place. You"re going to need a flex-head or universal joint and also different expansions - shot 1/4"-drive. The bolts weren"t in tight.... All that oil...- lower filter housing- Unplug sender from wire harness- On ground or vise, host housing and remove sender (24mm?). I just used big pliers, come out easy. Oil leaking from height of sender.- Clean housing- Swap o-ring- download in reverse. I must upload video to YouTube. It"s a 45 minute job. Spent an ext time in search of the oil press sender!